|
|
TG 300P
To satify the need for
ultimate welding quality presents "WIM Thyristor Controlled AC/DC PULSE TIG
Welder" most suitable single phase input & TIG arc welder for nonferrous metal. |
| S
P E C I F I C A T I O N S |
| |
Rating |
| |
|
TIG200 (with Pulse) |
TIG300 (with Pulse) |
TIG500 (with Pulse) |
| Input |
|
kVa |
17
(1Ø50/60Hz) |
26
(1Ø50/60Hz) |
51
(1Ø50/60Hz) |
| Duty cycle |
|
% |
40 |
60 |
| DC no load voltage |
|
V |
80 |
95 |
| AC no load voltage |
|
V |
80 |
100 |
| DC Out current |
TIG |
A |
5 ~ 200 |
5 ~ 300 |
5 ~ 500 |
| |
Manual |
A |
5 ~ 200 |
5 ~ 300 |
5 ~ 500 |
| DC Output voltage |
TIG |
V |
16 ~ 18 |
16 ~ 20 |
16 ~ 24 |
| |
Manual |
V |
20 ~ 28 |
20 ~ 32 |
20 ~ 40 |
| AC Output current |
TIG |
A |
20 ~ 200 |
20 ~ 300 |
20 ~ 500 |
| |
Manual |
A |
20 ~ 200 |
20 ~ 300 |
20 ~ 500 |
| AC Output voltage |
TIG |
V |
16 ~ 20 |
16 ~ 22 |
16 ~ 26 |
| |
Manual |
V |
20 ~ 30 |
20 ~ 35 |
20 ~ 40 |
| DC initial & Crater
current (TIG) |
A |
5 ~ 200 |
20 ~ 300 |
5 ~ 500 |
| AC initial & Crater
current (TIG) |
A |
20 ~ 200 |
20 ~ 300 |
20 ~ 500 |
| Initial current control |
|
Available
when Crater control On or Repitation |
| UP slope control time |
sec. |
0,
0.1~6(continuously) Adjustable to without control ( by P.C.B.) |
| Down slope control time |
sec. |
0,
0.2 ~ 10(continuously) Adjustable to without control (by P.C.B.) |
| Gas pre-flow time |
sec. |
0.3
(Changeable) |
| Gas after flow time |
sec. |
5
~ 25 (Continuously) |
| Arc spot time adjustment |
sec. |
0.5
~ 5 (Continuously) |
| Cleaning width adjustment |
|
Adjustable
with AC TIG welding |
| Pulse frequency |
Hz |
0.5
~ 10 (Continuously) |
| Dimension ( W x D x H) |
mm |
440
x 700 x 810 |
560 x 900 x
980 |
| Weight |
Kg. |
160 |
175 |
280 |
| Remote control |
|
Cable
length 4 m |
- It has good output characteristics, stable
arcing performance from the small current to rated current for welding of various
thicknesses of plates, especially suitable for thin plates.
- Very useful as power source for Butt welding
of thick plate and pipe which needs high quality and penetration bead.
- High quality welding, constant penetration
and stable welding bead can be obtained by the good arc concentration.
- Very easy to operate vertical welding, TIG
filler welding operation, tack welding for thin plate and repeated short length welding,
etc... by heat capacity control of pulse current. So, high efficiency welding can be done.
- Fine treatment and increase the weld quality
of welding start/finish with Up-slope control and Down-slope control.
- Precisely controls the arc conditions for
AC/DC manual welding of stainless-steel, special steel such as Cr-Mo steel by means of
refined electronics techniques so that optimum dynamic characteristics can be obtained.
- Improved digital control.
|
|
![[Company Logo Image]](_borders/WellLogo.jpg)
